Recherche avancée

Sur d’autres sites (4597)

• Monster Battery Power Revisited

  28 mai 2010, par Multimedia Mike — Python, Science Projects

  So I have this new fat netbook battery and I performed an experiment to determine how long it really lasts. In my last post on the matter, it was suggested that I should rely on the information that gnome-power-manager is giving me. However, I have rarely seen GPM report more than about 2 hours of charge ; even on a full battery, it only reports 3h25m when I profiled it as lasting over 5 hours in my typical use. So I started digging to understand how GPM gets its numbers and determine if, perhaps, it’s not getting accurate data from the system.

  I started poking around /proc for the data I wanted. You can learn a lot in /proc as long as you know the right question to ask. I had to remember what the power subsystem is called — ACPI — and this led me to /proc/acpi/battery/BAT0/state which has data such as :

  present :                 yes
  capacity state :          ok
  charging state :          charged
  present rate :            unknown
  remaining capacity :      100 mAh
  present voltage :         8326 mV
  

  "Remaining capacity" rated in mAh is a little odd ; I would later determine that this should actually be expressed as a percentage (i.e., 100% charge at the time of this reading). Examining the GPM source code, it seems to determine as a function of the current CPU load (queried via /proc/stat) and the battery state queried via a facility called devicekit. I couldn’t immediately find any source code to the latter but I was able to install a utility called ’devkit-power’. Mostly, it appears to rehash data already found in the above /proc file.

  Curiously, the file /proc/acpi/battery/BAT0/info, which displays essential information about the battery, reports the design capacity of my battery as only 4400 mAh which is true for the original battery ; the new monster battery is supposed to be 10400 mAh. I can imagine that all of these data points could be conspiring to under-report my remaining battery life.

  Science project : Repeat the previous power-related science project but also parse and track the remaining capacity and present voltage fields from the battery state proc file.

  Let’s skip straight to the results (which are consistent with my last set of results in terms of longevity) :

  
  
  

  So there is definitely something strange going on with the reporting— the 4400 mAh battery reports discharge at a linear rate while the 10400 mAh battery reports precipitous dropoff after 60%.

  Another curious item is that my script broke at first when there was 20% power remaining which, as you can imagine, is a really annoying time to discover such a bug. At that point, the "time to empty" reported by devkit-power jumped from 0 seconds to 20 hours (the first state change observed for that field).

  Here’s my script, this time elevated from Bash script to Python. It requires xdotool and devkit-power to be installed (both should be available in the package manager for a distro).
  

  PLAIN TEXT

  PYTHON :

  1. # !/usr/bin/python
  2.  
  3. import commands
  4. import random
  5. import sys
  6. import time
  7.  
  8. XDOTOOL = "/usr/bin/xdotool"
  9. BATTERY_STATE = "/proc/acpi/battery/BAT0/state"
  10. DEVKIT_POWER = "/usr/bin/devkit-power -i /org/freedesktop/DeviceKit/Power/devices/battery_BAT0"
  11.  
  12. print "count, unixtime, proc_remaining_capacity, proc_present_voltage, devkit_percentage, devkit_voltage"
  13.  
  14. count = 0
  15. while 1 :
  16.   commands.getstatusoutput("%s mousemove %d %d" % (XDOTOOL, random.randrange(0,800), random.randrange(0, 480)))
  17.   battery_state = open(BATTERY_STATE).read().splitlines()
  18.   for line in battery_state :
  19.     if line.startswith("remaining capacity :") :
  20.       proc_remaining_capacity = int(line.lstrip("remaining capacity : ").rstrip("mAh"))
  21.     elif line.startswith("present voltage :") :
  22.       proc_present_voltage = int(line.lstrip("present voltage : ").rstrip("mV"))
  23.   devkit_state = commands.getoutput(DEVKIT_POWER).splitlines()
  24.   for line in devkit_state :
  25.     line = line.strip()
  26.     if line.startswith("percentage :") :
  27.       devkit_percentage = int(line.lstrip("percentage :").rstrip(’\%’))
  28.     elif line.startswith("voltage :") :
  29.       devkit_voltage = float(line.lstrip("voltage :").rstrip(’V’)) * 1000
  30.   print "%d, %d, %d, %d, %d, %d" % (count, time.time(), proc_remaining_capacity, proc_present_voltage, devkit_percentage, devkit_voltage)
  31.   sys.stdout.flush()
  32.   time.sleep(60)
  33.   count += 1

• MPEG DASH : frame seeking

  13 août 2014, par bisc8

  TL ;DR : Is it possible to achieve frame seeking using DASH ? How ?

  I’m using ffmpeg to create non-multiplexed content :

  ffmpeg -y -an -codec:v libx264 -profile:v baseline output_video.mp4 -i video.mp4
  
  ffmpeg -y -vn -codec:a libvo_aacenc -ac 1 -ar 44100 output_audio.mp4 -i video.mp4

  Then I’m using mp4box to create DASH content :

  mp4box -dash 10000 -frag 1000 -rap -dash-profile live -segment-name mp4-live-$RepresentationID$-$Number$ -out manifest.mpd output_video.mp4 output_audio.mp4

  Finally I open the generated content with Chrome, using dash.js. Everything works fine except that I can’t do frame seek. I keep on adding (1/frame_rate) seconds to the current time but nothing happens, the frame only changes after 10 seconds.

  I suppose this has to do with the video’s key interval. However, I am able to do frame seek after the ffmpeg part, so I guess I’m missing something in the mp4box command.

  Is it possible to achieve frame seeking using DASH or am I missing something ?

  Thanks in advance.

• CD-R Read Speed Experiments

  21 mai 2011, par Multimedia Mike — Science Projects, Sega Dreamcast

  I want to know how fast I can really read data from a CD-R. Pursuant to my previous musings on this subject, I was informed that it is inadequate to profile reading just any file from a CD-R since data might be read faster or slower depending on whether the data is closer to the inside or the outside of the disc.

  Conclusion / Executive Summary
  It is 100% true that reading data from the outside of a CD-R is faster than reading data from the inside. Read on if you care to know the details of how I arrived at this conclusion, and to find out just how much speed advantage there is to reading from the outside rather than the inside.

  Science Project Outline

  • Create some sample CD-Rs with various properties
  • Get a variety of optical drives
  • Write a custom program that profiles the read speed

  Creating The Test Media
  It’s my understanding that not all CD-Rs are created equal. Fortunately, I have 3 spindles of media handy : Some plain-looking Memorex discs, some rather flamboyant Maxell discs, and those 80mm TDK discs :

  
  
  

  My approach for burning is to create a single file to be burned into a standard ISO-9660 filesystem. The size of the file will be the advertised length of the CD-R minus 1 megabyte for overhead— so, 699 MB for the 120mm discs, 209 MB for the 80mm disc. The file will contain a repeating sequence of 0..0xFF bytes.

  Profiling
  I don’t want to leave this to the vagaries of any filesystem handling layer so I will conduct this experiment at the sector level. Profiling program outline :

  • Read the CD-ROM TOC and get the number of sectors that comprise the data track
  • Profile reading the first 20 MB of sectors
  • Profile reading 20 MB of sectors in the middle of the track
  • Profile reading the last 20 MB of sectors

  Unfortunately, I couldn’t figure out the raw sector reading on modern Linux incarnations (which is annoying since I remember it being pretty straightforward years ago). So I left it to the filesystem after all. New algorithm :

  • Open the single, large file on the CD-R and query the file length
  • Profile reading the first 20 MB of data, 512 kbytes at a time
  • Profile reading 20 MB of sectors in the middle of the track (starting from filesize / 2 - 10 MB), 512 kbytes at a time
  • Profile reading the last 20 MB of sectors (starting from filesize - 20MB), 512 kbytes at a time

  Empirical Data
  I tested the program in Linux using an LG Slim external multi-drive (seen at the top of the pile in this post) and one of my Sega Dreamcast units. I gathered the median value of 3 runs for each area (inner, middle, and outer). I also conducted a buffer flush in between Linux runs (as root : 'sync; echo 3 > /proc/sys/vm/drop_caches').

  LG Slim external multi-drive (reading from inner, middle, and outer areas in kbytes/sec) :

  • TDK-80mm : 721, 897, 1048
  • Memorex-120mm : 1601, 2805, 3623
  • Maxell-120mm : 1660, 2806, 3624

  So the 120mm discs can range from about 10.5X all the way up to a full 24X on this drive. For whatever reason, the 80mm disc fares a bit worse — even at the inner track — with a range of 4.8X - 7X.

  Sega Dreamcast (reading from inner, middle, and outer areas in kbytes/sec) :

  • TDK-80mm : 502, 632, 749
  • Memorex-120mm : 499, 889, 1143
  • Maxell-120mm : 500, 890, 1156

  It’s interesting that the 80mm disc performed comparably to the 120mm discs in the Dreamcast, in contrast to the LG Slim drive. Also, the results are consistent with my previous profiling experiments, which largely only touched the inner area. The read speeds range from 3.3X - 7.7X. The middle of a 120mm disc reads at about 6X.

  Implications
  A few thoughts regarding these results :

  • Since the very definition of 1X is the minimum speed necessary to stream data from an audio CD, then presumably, original 1X CD-ROM drives would have needed to be capable of reading 1X from the inner area. I wonder what the max read speed at the outer edges was ? It’s unlikely I would be able to get a 1X drive working easily in this day and age since the earliest CD-ROM drives required custom controllers.
  • I think 24X is the max rated read speed for CD-Rs, at least for this drive. This implies that the marketing literature only cites the best possible numbers. I guess this is no surprise, similar to how monitors and TVs have always been measured by their diagonal dimension.
  • Given this data, how do you engineer an ISO-9660 filesystem image so that the timing-sensitive multimedia files live on the outermost track ? In the Dreamcast case, if you can guarantee your FMV files will live somewhere between the middle and the end of the disc, you should be able to count on a bitrate of at least 900 kbytes/sec.

  Source Code
  Here is the program I wrote for profiling. Note that the filename is hardcoded (#define FILENAME). Compiling for Linux is a simple 'gcc -Wall profile-cdr.c -o profile-cdr'. Compiling for Dreamcast is performed in the standard KallistiOS manner (people skilled in the art already know what they need to know) ; the only variation is to compile with the '-D_arch_dreamcast' flag, which the default KOS environment adds anyway.

  PLAIN TEXT

  C :

  1. #ifdef _arch_dreamcast
  2.   #include <kos .h>
  3.  
  4.   /* map I/O functions to their KOS equivalents */
  5.   #define open fs_open
  6.   #define lseek fs_seek
  7.   #define read fs_read
  8.   #define close fs_close
  9.  
  10.   #define FILENAME "/cd/bigfile"
  11. #else
  12.   #include <stdio .h>
  13.   #include <sys /types.h>
  14.   #include </sys><sys /stat.h>
  15.   #include </sys><sys /time.h>
  16.   #include <fcntl .h>
  17.   #include <unistd .h>
  18.  
  19.   #define FILENAME "/media/Full disc/bigfile"
  20. #endif
  21.  
  22. /* Get a current absolute millisecond count ; it doesn’t have to be in
  23. * reference to anything special. */
  24. unsigned int get_current_milliseconds()
  25. {
  26. #ifdef _arch_dreamcast
  27.   return timer_ms_gettime64() ;
  28. #else
  29.   struct timeval tv ;
  30.   gettimeofday(&tv, NULL) ;
  31.   return tv.tv_sec * 1000 + tv.tv_usec / 1000 ;
  32. #endif
  33. }
  34.  
  35. #define READ_SIZE (20 * 1024 * 1024)
  36. #define READ_BUFFER_SIZE (512 * 1024)
  37.  
  38. int main()
  39. {
  40.   int i, j ;
  41.   int fd ;
  42.   char read_buffer[READ_BUFFER_SIZE] ;
  43.   off_t filesize ;
  44.   unsigned int start_time, end_time ;
  45.  
  46.   fd = open(FILENAME, O_RDONLY) ;
  47.   if (fd == -1)
  48.   {
  49.     printf("could not open %s\n", FILENAME) ;
  50.     return 1 ;
  51.   }
  52.   filesize = lseek(fd, 0, SEEK_END) ;
  53.  
  54.   for (i = 0 ; i <3 ; i++)
  55.   {
  56.     if (i == 0)
  57.     {
  58.       printf("reading inner 20 MB...\n") ;
  59.       lseek(fd, 0, SEEK_SET) ;
  60.     }
  61.     else if (i == 1)
  62.     {
  63.       printf("reading middle 20 MB...\n") ;
  64.       lseek(fd, (filesize / 2) - (READ_SIZE / 2), SEEK_SET) ;
  65.     }
  66.     else
  67.     {
  68.       printf("reading outer 20 MB...\n") ;
  69.       lseek(fd, filesize - READ_SIZE, SEEK_SET) ;
  70.     }
  71.     /* read 20 MB ; 40 chunks of 1/2 MB */
  72.     start_time = get_current_milliseconds() ;
  73.     for (j = 0 ; j <(READ_SIZE / READ_BUFFER_SIZE) ; j++)
  74.       if (read(fd, read_buffer, READ_BUFFER_SIZE) != READ_BUFFER_SIZE)
  75.       {
  76.         printf("read error\n") ;
  77.         break ;
  78.       }
  79.     end_time = get_current_milliseconds() ;
  80.     printf("%d - %d = %d ms => %d kbytes/sec\n",
  81.       end_time, start_time, end_time - start_time,
  82.       READ_SIZE / (end_time - start_time)) ;
  83.   }
  84.  
  85.   close(fd) ;
  86.  
  87.   return 0 ;
  88. }