Recherche avancée

Sur d’autres sites (6475)

• lavc/qsvenc : set HRD buffer size

  1er décembre 2017, par Li, Zhong

  lavc/qsvenc : set HRD buffer size
  Hypothetical Reference Decoding (HRD) model assumes that data flows
  
  into a buffer of the fixed size BufferSizeInKB with a constant bitrate.
  
  Smaller BufferSizeInKB means smaller frame size variations,
  
  but more difficult to maintain HRD.
  Signed-off-by : Zhong Li <zhong.li@intel.com>
  
  Signed-off-by : Maxym Dmytrychenko <maxim.d33@gmail.com>
  

  • [DBH] libavcodec/qsvenc.c

• How to change ffmpeg -threads settings [migrated]

  5 août 2014, par Jacob

  Working on a tube site. I’m running videos through ffmpeg on a linux dedicated server to convert to mp4.

  The server specs :

  Architecture:          x86_64
  
  CPU op-mode(s):        32-bit, 64-bit
  
  Byte Order:            Little Endian
  
  CPU(s):                8
  
  On-line CPU(s) list:   0-7
  
  Thread(s) per core:    2
  
  Core(s) per socket:    4
  
  Socket(s):             1
  
  NUMA node(s):          1
  
  Vendor ID:             GenuineIntel
  
  CPU family:            6
  
  Model:                 60
  
  Stepping:              3
  
  CPU MHz:               3491.749
  
  BogoMIPS:              6983.49
  
  Virtualization:        VT-x
  
  L1d cache:             32K
  
  L1i cache:             32K
  
  L2 cache:              256K
  
  L3 cache:              8192K
  
  NUMA node0 CPU(s):     0-7

  Issue during testing is that even only doing 4-5 at once, the server load skyrockets to an average of around 36. This is just a single person. I imagine when it opens, many people will be uploading at once.

  It seems ffmpeg tries to use all the resources available per conversion.

  I’ve heard there’s a -threads setting you can change, but I cannot find it. I have an 8 cpu server. It’s only used for conversions, so I’ve heard the best setting would be between 2 and 4. I can test it out.

  But how do I change this setting ? Everything I see online discusses this setting, but not the steps to change it.

• ffmpeg settings or alternatives to ffmpeg on raspberry pi for video streaming

  14 octobre 2016, par andrei

  I have a Raspberry Pi (model B) running raspbian wheezy on a 16gb SD card. I also have a 32gb flash storage attached on the usb. I’m trying to stream a video (h264 encoded mp4 file 1280x720) over the ethernet from that flash storage.
  I’m using ffmpeg+ffserver. Here is ffserver.conf (relevant parts) :

  ...
  
  MaxBandwidth 10000
  
  <feed>
  
  ...
  
  FileMaxSize 100M
  
  ACL allow 127.0.0.1
  
  </feed>
  
  ...
  
  <stream>
  
  Feed feed1.ffm
  
  Format flv
  
  VideoSize 288x176 #made small just for testing
  
  NoAudio
  
  </stream>
  
  ....

  I start the ffserver, then call ffmpeg with this command :

  ffmpeg -re -an -i /mnt/u32/main.mp4 -r 25 -bit_rate 300k http://localhost:8090/feed1.ffm

  And I’m getting fps 3-5 at most. Naturally when I try to view the stream on another computer it’s very choppy and virtually unusable.

  Am I missing some settings ? Or perhaps there is another streaming solution that leverages the GPU instead of just the CPU as ffmpeg does ? I’m even open to suggestions about other boards (e.g. a pandaboard ? or clustering several RPi’s ?) Also, I’m flexible about the output format.