Recherche avancée

Sur d’autres sites (8872)

• FFMPEG Seeking with concat demuxer causes video & audio to be out of sync

  20 février 2023, par Garuuk

  I have a very simple use case that's driving me bananas.

  


  My problem and question :

  


  I'm using ffmpeg version 5.1.2 on a MacOS and i'm using ffmpeg seeking and concat demuxer to cut many 1 minute videos into 15 seconds chopped up over 12 clips where every clip is just 2 seconds from the same video (kind of like a mini teasers for the video). I would really like to not have to re-encode to make the video processing as fast as possible.

  


  First, I take each 1 minute video and cut it up into 12 clips (I do all this programmatically in python fwiw)

  


  ffmpeg -ss 0 -i input.mp4 -t 2 -c copy -y cut_1.mp4
ffmpeg -ss 4 -i input.mp4 -t 2 -c copy -y cut_2.mp4
ffmpeg -ss 8 -i input.mp4 -t 2 -c copy -y cut_3.mp4
...
...


  


  I then write all the output file names to my concat_manifest.txt

  


  file cut_1.mp4
file cut_2.mp4
...
...


  


  Then I run my concat command :

  


  ffmpeg -f concat -i concat_manifest.txt -c copy -y concat_video.mp4


  


  This works really fast but the audio and video at the stitch point get out of sync and sometimes the video just chokes & lags. It's mostly not a smooth experience.

  


  What I have tried :

  


  

  1. using the concat protocol with intermediate profiles : ffmpeg.org/wiki/Concatenate#demuxer

  


  2. Putting the -ss when I seek after the -i. This makes everything worse

  


  3. Playing around with different -ss values. This has some noticeable affects but it's not obvious why yet.

  


  4. I've also read from the ffmpeg resource regarding seeking and copying :

  


  


  Which leads me to believe that maybe because ffmpeg is using timestamps instead of frames, seeking isn't accurate using -ss when using the concat demuxer

  


  Is there a way to get concat demuxer cutting and concatenating the video where the audio is somewhat in sync with the video ?

  


  Thanks

  


  EDIT : I found an answer and i'll be posting the solution in the coming few days.

  


• FFmpeg, how to skip late input ?

  14 novembre 2017, par user3343357

  I’m running ffmpeg to display incoming stream on a Decklink BlackMagic card with the following command line :

  ffmpeg -y -f ourFmt -probesize 32 -i - -f decklink -preset ultrafast 
  
     -pix_fmt uyvy422 -s 1920x1080 -r 30 -af volume=0.1 -max_delay 10000 
  
       DeckLink Mini Monitor

  Basically I get the video over the internet by UDP and stream it to ffmpeg stdin. Both audio and video streams have pts and dts and are fully in sync, if the connection is good there is no problems.

  However if there are issues with the connection i start getting errors, sometimes the video delay grows significantly, and audio stops working.
  The errors i get are :

  ffmpeg : [decklink @ 0x26cc600] There are not enough buffered video
  frames. Video may misbehave ! ffmpeg : [decklink @ 0x26cc600] There’s no
  buffered audio. Audio will misbehave ! ffmpeg : Last message
  repeated 4 times ffmpeg : [decklink @ 0x26cc600] There are not enough
  buffered video frames. Video may misbehave ! ffmpeg : [decklink @
  0x26cc600] There’s no buffered audio. Audio will misbehave ! ffmpeg :
  Last message repeated 3 times ffmpeg : frame= 5204 fps= 30 q=-0.0
  size=N/A time=00:02:53.76 bitrate=N/A dup=385 drop=5 speed=0.993x
  ffmpeg : [decklink @ 0x26cc600] There’s no buffered audio. Audio will
  misbehave ! ffmpeg : Last message repeated 18 times ffmpeg :
  [decklink @ 0x26cc600] There are not enough buffered video frames.
  Video may misbehave ! ffmpeg : [decklink @ 0x26cc600] There’s no
  buffered audio. Audio will misbehave !

  The problem is when the connection is back to normal, the video keeps misbehaving until I restart the stream. What I want to do is for FFmpeg to skip to the content of the last second and play synchronized video from there, drop all the late data in between, is it possible ?

• Find video resolution and video duration of remote mediafile

  22 février 2012, par osgx

  I want to write an program which can find some metainformation of mediafile. I'm interested in popular video formats, such as avi, mkv, mp4, mov (may be other popular too). I want basically to get :

  • Video size (720, 1080, 360 etc)
  • Total runtime of video (may be not very exact)
  • Number of audio streams
  • Name of video codec
  • Name of audio codec

  There is already the mediainfo, but in my program I want to get information about remote file, which may be accessed via ftp, http, samba ; or even torrent (there are some torrent solutions, which allows to read not-yet downloaded file).

  MediaInfo library have no support of samba (smb ://) and mkv format (for runtime).

  Also, I want to know, how much data should be downloaded to get this information. I want not to download full videofile because I have no enough disk space.

  Is this information in the first 1 or 10 or 100 KiloBytes of the file ? Is it at predictable offset if I know the container name and total file size ?

  PS : Platform is Linux, Language is C/C++