Recherche avancée

Sur d’autres sites (9551)

• How can i make ffmpeg pick the right file ?

  20 septembre 2019, par A Person

  I’ve been trying to make ffmpeg pick up files from a folder and merge them together.

  The code i have for merging the audio and video is :

  ffmpeg -i video.m2v -i audio.wav -c copy -map 0:0 -map 1:0 %orginal_name%.mxf

  This works but i chnage the %origninal_name to the name of the video file.

  Im currently using a watch folder in FFAStrans to pick the video file up and using custom ffmpeg comand to run the command. The problem i’m having is that i have to specify the video and audio file name.

  The folder has over 100 video and audio file and they have the same name so if ita s food show it would be

  category_name_episode_HighRandomVariable.m2v for video
  category_name_episode_HighRandomVariableDifferentFromVideo.wav for audio
  example of this is
  food_johnsCooking_EP1_High745548.m2v and
  food_johnsCooking_EP1_High8547885874.wav

  im using regext as well but dont really know how to use in in FFAStrans but the command looks like this.
  $regext("%s_original_name%","(.+)_High")

  Does anyone know how i can set it up so i can get the correct audio and video file to merge and at the same time make sure all other videos and audio files are done without me having to change the ffmpeg -i to the next video and audio name.

  Any Help or advice is appreciated.

  Many thanks in advance.

• ffmpeg QSV hardware encoder with x11grab screen capture

  11 janvier 2020, par Toby Eggitt

  I believe I have built ffmpeg with support for my motherboard’s Intel graphics processor chip, but I have not succeeded in showing this working in any way. My goal is to use it for screen capture (the ffmpeg I built does capture screen successfully using the software encoding, but this is far too slow to be useful—it manages about 12fps at a very modest quality).

  My main problem—I think—is that I don’t know how to use these encoders, the examples I found all fail, which makes me suspect that what I’ve built is broken in some way. However, I also have no idea how I can verify that I built this correctly, but the following are true :

  • The five components that I built to get to this all compiled without
    errors (they were libva, gmmlib, intel-media-driver, libmfx, and
    ffmpeg
  • The output of ffmpeg -encoders includes four encoders with _qsv in
    their names including h264_qsv
  • Most of the commands I have tried result in output of this form :

      [h264_qsv @ 0x55ef1dc72040] Low power mode is unsupported
  
      [h264_qsv @ 0x55ef1dc72040] Current frame rate is unsupported
  
      [h264_qsv @ 0x55ef1dc72040] Current picture structure is unsupported
  
      [h264_qsv @ 0x55ef1dc72040] Current resolution is unsupported
  
      [h264_qsv @ 0x55ef1dc72040] Current pixel format is unsupported
  
      [h264_qsv @ 0x55ef1dc72040] some encoding parameters are not supported by the QSV runtime. Please double check the input parameters.
  
      Error initializing output stream 0:0 -- Error while opening encoder for output stream #0:0 - maybe incorrect parameters such as bit_rate, rate, width or height

  I have the impression this thing might be fussy about many parameters of this sort but have no idea where to find out what it would like. Any suggestions at all, how to verify it, or better yet, how to issue a command that captures screen and encodes with the hardware, would be most welcome.

• How to handle differing .mp4 file types from different sources ?

  10 octobre 2017, par Dave502619

  If I take a .mp4 recorded on my mobile (Samsung S5) and pass it through FFmpeg with the below command, the output file (fileX.avi) is a greyscale bitmap uncompressed video file.

  • The offset values in fileX.avi (output from FFmpeg) to allow me to locate the video frame data are always 5680 bytes for the file header.

  • And 62 bytes for the inter frame header.

  • The data is uncompressed RGB24 so i can easily calculate the size of a video frame from height x width x 3.

  So my C# application can access the video frames in fileX.avi always at these above offsets.
  (This works great).

  My FFmpeg Command is :

  ffmpeg.exe -i source.mp4 -b 1150 -r 20.97 -g 120 -an -vf format=gray -f rawvideo -pixfmt gray -s 384x216 -vcodec rawvideo -y fileX.avi

  However... I recently took an .mp4 file from a different source (produced by Power Director 14 instead of direct from my mobile phone) and used this as the input source.mp4. But now the structure of fileX.avi differs as the offset values of 5680 + 62 bytes from the start in fileX.avi do not land me at the start of the video data frames.

  There seems to be different file formats for .mp4 - and obviously if there are my crude offset approach will not work for them all. I suspected at the time I wrote the code my method was all too easy a solution !

  So can anyone advise on the approach I should take now ? Should I check the original .mp4 or the output file (fileX.avi) to determine a "file type" to which I can determine the different offsets ?

  At the very least I need to be able to identify the "type" of .mp4 file that works so I can declare the type that will work with my software.