Recherche avancée

Médias (91)

Autres articles (63)

  • MediaSPIP 0.1 Beta version

    25 avril 2011, par

    MediaSPIP 0.1 beta is the first version of MediaSPIP proclaimed as "usable".
    The zip file provided here only contains the sources of MediaSPIP in its standalone version.
    To get a working installation, you must manually install all-software dependencies on the server.
    If you want to use this archive for an installation in "farm mode", you will also need to proceed to other manual (...)

  • MediaSPIP version 0.1 Beta

    16 avril 2011, par

    MediaSPIP 0.1 beta est la première version de MediaSPIP décrétée comme "utilisable".
    Le fichier zip ici présent contient uniquement les sources de MediaSPIP en version standalone.
    Pour avoir une installation fonctionnelle, il est nécessaire d’installer manuellement l’ensemble des dépendances logicielles sur le serveur.
    Si vous souhaitez utiliser cette archive pour une installation en mode ferme, il vous faudra également procéder à d’autres modifications (...)

  • Amélioration de la version de base

    13 septembre 2013

    Jolie sélection multiple
    Le plugin Chosen permet d’améliorer l’ergonomie des champs de sélection multiple. Voir les deux images suivantes pour comparer.
    Il suffit pour cela d’activer le plugin Chosen (Configuration générale du site > Gestion des plugins), puis de configurer le plugin (Les squelettes > Chosen) en activant l’utilisation de Chosen dans le site public et en spécifiant les éléments de formulaires à améliorer, par exemple select[multiple] pour les listes à sélection multiple (...)

Sur d’autres sites (6662)

  • getting ffmpeg to listen on specific port on amazon ec2

    12 juillet 2013, par user1913115

    I have a streaming device which can stream to any udp address/port, so if i set it up on my network , and open ffmpeg with this command :

    ffmpeg -f mpegts -i 'udp://0.0.0.0:2223?fifo_size=1000000&overrun_nonfatal=1' -re -y -strict experimental -vcodec copy -f mp4 main.mp4

    it works fine, i get the main.mp4 file recorded.
    also, when i check lsof -i it shows that ffmpeg is listening on port 2223

    however, when i run the same command on amazon ec2, it doesn't record anything. i checked, the port 2223 is open in the security group. and if i run this command, it gets packets fine :

    nc -u -l 2223

    however when i run lsof -i in amazon ec2 it shows that ffmpeg is listening to a random UDP port (e.g. 42195) every time
    has anyone run into this problem ?

  • Intsallation of ffmpeg-php on Amazon Ec2 Linux AMI

    1er décembre 2015, par Tanny

    I am about two days into attempting to install FFMPEG-php with dependencies on an AWS EC2 instance running the Amazon Linux AMI. I’ve installed FFMPEG, and have read reportedly successful instructions on installing on Red Hat/Fedora. I have followed a number of tutorials and forum articles to do so, but have had no luck yet. As far as I can tell, the main problems are as followed :

    I have installed all the dependency for ffmpeg-php. I run the following command successfully.

    $wget http://downloads.sourceforge.net/project/ffmpeg-php/ffmpeg-php/0.6.0/ffmpeg-php-0.6.0.tbz2
    $tar xvfj ffmpeg-php-0.6.0.tbz2
    $phpize

    But when I run the following command it throw the error like below :

    $sudo ./configure

    configure : error : ffmpeg shared libraries not found. Make sure ffmpeg is compiled as shared libraries using the —enable-shared option}

    I have used enable shared option with shared enable option but it throw the same error.

    On to my question : Has anyone successfully installed FFMPEG-php on Amazon Linux ? Is there a fundamental incompatibility ? If anyone could share specific instructions on installing ffmpeg-php on amazon linux I would be greatly appreciative. Any other insights/experiences would also be appreciated.

  • Fire events at specific timestamps during video playback

    27 octobre 2017, par Simon

    I’m using a Raspberry Pi 3 running Raspbian. I need to play a video file via HDMI, and I need events to be fired at specific timecodes during the playback of the video. The events are simple write operations to the GPIO. My problem is : what approach should I use to do this ?

    My first approach was to use OpenCv (python) and VideoCapture(), but the raspberry pi is too slow, and my FPS is very low (I need at least 25 FPS @ 1080p).

    So now I’m looking into other solutions : Gstreamer, FFMPEG, omxplayer, I read the documentations but I can’t figure out which tool to use for this job.

Navigation