Recherche avancée

Sur d’autres sites (9644)

• FFMPEG & MistServer : RTMP Input/Output error

  17 octobre 2017, par brewcrazy

  I have an IP camera that outputs a RTSP stream that I’m trying to use to display a live feed on my website. This is a small site that only my wife and I will access so I’m trying to use a free streaming service. For that reason, I’ve decided to try MistServer’s open source option.

  I currently have downloaded MistServer and have it running without installation on my mac (sudo ./MistController). With MistServer running, I have a stream set up and default protocols configured. The stream is configured as follows :

  stream name: ipcam
  
  source: push://

  The configuration page gives me the following source to push to :

  RTMP full url: rtmp://127.0.0.1/live/ipcam
  
  RTMP url: rtmp://127.0.0.1/live/
  
  RTMP stream key: ipcam

  In the streams view, the stream’s status is unavailable, but I’m assuming this is because it isn’t receiving an input. I haven’t been able to confirm this via documentation.

  Here is the FFMPEG command that I am running and the error that I’m getting :

  ffmpeg -rtsp_transport tcp -i rtsp://<user>:@:554/live0.264 -acodec copy -vcodec copy -f flv rtmp://127.0.0.1/live/ipcam
  
  
  
  ffmpeg version 3.3.3 Copyright (c) 2000-2017 the FFmpeg developers
  
    built with Apple LLVM version 8.1.0 (clang-802.0.42)
  
    configuration: --prefix=/usr/local/Cellar/ffmpeg/3.3.3 --enable-shared --enable-pthreads --enable-gpl --enable-version3 --enable-hardcoded-tables --enable-avresample --cc=clang --host-cflags= --host-ldflags= --enable-libmp3lame --enable-libx264 --enable-libxvid --enable-opencl --enable-videotoolbox --disable-lzma --enable-vda
  
    libavutil      55. 58.100 / 55. 58.100
  
    libavcodec     57. 89.100 / 57. 89.100
  
    libavformat    57. 71.100 / 57. 71.100
  
    libavdevice    57.  6.100 / 57.  6.100
  
    libavfilter     6. 82.100 /  6. 82.100
  
    libavresample   3.  5.  0 /  3.  5.  0
  
    libswscale      4.  6.100 /  4.  6.100
  
    libswresample   2.  7.100 /  2.  7.100
  
    libpostproc    54.  5.100 / 54.  5.100
  
  Guessed Channel Layout for Input Stream #0.1 : mono
  
  Input #0, rtsp, from 'rtsp://<user>:@:554/live0.264':
  
    Metadata:
  
      title           : Session Streamed by LIBZRTSP
  
      comment         : live0.264
  
    Duration: N/A, start: 0.242000, bitrate: N/A
  
      Stream #0:0: Video: h264 (Main), yuv420p(progressive), 1280x720, 25 fps, 24.83 tbr, 90k tbn, 50 tbc
  
      Stream #0:1: Audio: pcm_mulaw, 8000 Hz, mono, s16, 64 kb/s
  
  rtmp://127.0.0.1/live/ipcam: Input/output error
  
  </user></user>

  I can’t determine from this error if the issue is the FFMPEG command or my MistServer configuration.

• How to handle differing .mp4 file types from different sources ?

  10 octobre 2017, par Dave502619

  If I take a .mp4 recorded on my mobile (Samsung S5) and pass it through FFmpeg with the below command, the output file (fileX.avi) is a greyscale bitmap uncompressed video file.

  • The offset values in fileX.avi (output from FFmpeg) to allow me to locate the video frame data are always 5680 bytes for the file header.

  • And 62 bytes for the inter frame header.

  • The data is uncompressed RGB24 so i can easily calculate the size of a video frame from height x width x 3.

  So my C# application can access the video frames in fileX.avi always at these above offsets.
  (This works great).

  My FFmpeg Command is :

  ffmpeg.exe -i source.mp4 -b 1150 -r 20.97 -g 120 -an -vf format=gray -f rawvideo -pixfmt gray -s 384x216 -vcodec rawvideo -y fileX.avi

  However... I recently took an .mp4 file from a different source (produced by Power Director 14 instead of direct from my mobile phone) and used this as the input source.mp4. But now the structure of fileX.avi differs as the offset values of 5680 + 62 bytes from the start in fileX.avi do not land me at the start of the video data frames.

  There seems to be different file formats for .mp4 - and obviously if there are my crude offset approach will not work for them all. I suspected at the time I wrote the code my method was all too easy a solution !

  So can anyone advise on the approach I should take now ? Should I check the original .mp4 or the output file (fileX.avi) to determine a "file type" to which I can determine the different offsets ?

  At the very least I need to be able to identify the "type" of .mp4 file that works so I can declare the type that will work with my software.

• Convert a Video_TS dir to a single mp4 or mkv file ?

  29 août 2018, par RocketNuts

  I’ve got a file-to-file copy from a DVD, consisting of a Video_TS directory with a bunch of BUP, IFO and VOB files. I can open some (not all) of these files in a player like VLC, and it seems to contain fragments of the movie but it appears like garbage. As if the encoding or file structure is corrupted.

  However, if I open the entire Video_TS dir with VLC, it plays fine.

  Is there a way to convert this Video_TS dir to one single video file, such as an MP4 or MKV ?

  I’ve read about the possibility of binary concatenating the VOB files, and I tried that, but to no avail. Also I wouldn’t know how to the determine the exact order of the VOB files, and more importantly that information must be within the files itself somehow (considering that video players can play it automatically).

  (edit) Someone edited the question and removed the ffmpeg part. Sorry if I didn’t clarify this further : I’m actually explicitly looking for a way to do this with ffmpeg (from shell, on macOS).