Sur d’autres sites (7988)

• How to run FFMPEG with —enable-libfontconfig on Amazon Linux 2

  22 avril 2024, par Adrien Kaczmarek

  Problem

  


  I want to run FFmpeg on AWS Lambda (Amazon Linux 2) with the configuration --enable-libfontconfig enable.

  


  Situation

  


  I already have FFmpeg running on AWS Lambda without the configuration --enable-libfontconfig.

  


  Here is the step I took to run FFmpeg on AWS Lambda (see official guide) :

  


  

  • Connect to Amazon EC2 running on AL2 (environment used by Lambda for Python 3.11)

  


  • Download and package FFmpeg from John Van Sickle

  


  • Create a Lambda Layer with FFmpeg

  


  


  Unfortunately, the version built by John Van Sickle doesn't have the configuration --enable-libfontconfig enabled.

  


  Unsuccessful Trials

  


  I tried to rebuilt it from scratch following the installation guide but without success (and the guide doesn't install font related dependencies)

  


  I tried to install it with brew but the command brew install ffmpeg didn't succeed on AL2.

  


  I tried to install ffmpeg from ffmpeg-master-latest-linux64-gpl.tar.xz. Unfortunately, this build of ffmpeg doesn't run on AL2 :

  


  ffmpeg: /lib64/libm.so.6: version `GLIBC_2.27' not found (required by ffmpeg)
ffmpeg: /lib64/libpthread.so.0: version `GLIBC_2.28' not found (required by ffmpeg)
ffmpeg: /lib64/libc.so.6: version `GLIBC_2.27' not found (required by ffmpeg)
ffmpeg: /lib64/libc.so.6: version `GLIBC_2.28' not found (required by ffmpeg)


  


  Any help would be greatly appreciated,

  


  Please make sure your answer is up to date and tested. Too many answers out there are auto-generated, too generic, or simple redirect without context.

  


  Thank you

  


• How to generating waveform from video & show it with video

  25 novembre 2016, par Salil

  We are using Rails as a backend & AngularJS on Front End side in my App where we need to show Video & audio waveform of that video.

  We are using ’wavesurfer.js’ to show the waveform on Front End side & ’node-pcm’ to generate pcm from video file on BackEnd side.

  This is working as expected but in some of the videos while creating waveform from pcm data instead of showing small sine waves we get flat line.
  Also it takes too much time to show the waveform for every page reload.

  To overcome this issue we are planning to create waveform image using ffmpeg

  ffmpeg -i 'https://s3.amazonaws.com/aadasdsadsadasdas/xyz.mp4' -filter_complex showwavespic -frames:v 1 output.png

  This is working fine but it also takes too much time (Ofcourse only once ) to generate the image for remote video (i.e. We are saving videos on S3)

  Problem with this i don’t get any library to integrate the waveform image with the Video.

  Can someone suggest any better approach related to this.

• FFMPEG - Streaming GoPro4 to RSTP

  20 mai 2017, par Winged

  Greeting !
  I’m planning to capture a realtime streaming video from GoPro4 and load it into TouchDesigner in order to use this footage in a projection mapping project.

  So far I was able to play GoPro4 stream using ffplay doing as follows :
  1. Host GoPro4 WiFi hotspot.
  2. Connect a laptop WiFi to GoPro4’s hotspot.
  3. Restart GoPro stream service by opening ’http://10.5.5.9/gp/gpControl/execute?p1=gpStream&c1=restart’ in s browser.
  4. Run ffplay command in order to open ffplay stream video window : ’ffplay -an -fflags nobuffer -f:v mpegts -probesize 8192 rtp ://10.5.5.9:8554’

  The next step I opt to make it to re-stream this signal into RTSP protocol so TouchDesigner could receive this signal.

  And here is my question - how to re-stream this input to RTSP ?